SUBARU impreza SERVICE and USER MANUAL

CONTROL SYSTEMS

Sort by: default name
Select Lever ASSEMBLY Select Lever ASSEMBLY CONTROL SYSTEMS > Select Lever ASSEMBLY 1. Clean all the parts before assembly. 2. Apply Multemp D or equivalent to the sliding portion of each part. 3. Assemble in the reverse order of disassembly. NOTE:...
Select Lever DISASSEMBLY Select Lever DISASSEMBLY CONTROL SYSTEMS > Select Lever DISASSEMBLY 1. GRIP ASSY 1. Remove the button assembly_AT. (A) Claw 2. Remove the rod COMPL. 2. AT SELECT LEVER ASSEMBLY 1. Remove the spacer plate....
Select Lever INSTALLATION Select Lever INSTALLATION CONTROL SYSTEMS > Select Lever INSTALLATION 1. Set the select lever assembly to the vehicle body. 2. Tighten the four mounting bolts to attach the select lever assembly to the vehicle body. Tightening torque: 18...
Select Lever REMOVAL Select Lever REMOVAL CONTROL SYSTEMS > Select Lever REMOVAL 1. Shift the select lever to “N” range. 2. Disconnect the ground cable from battery. NOTE NOTE: For the 12 volt engine restart battery of HEV model, disconnect...
Select Cable INSTALLATION Select Cable INSTALLATION CONTROL SYSTEMS > Select Cable INSTALLATION 1. Position the select cable as shown in the figure, and install it to the plate assembly. CAUTION: • If the cable is installed in the wrong direction, loosen the...
Select Cable ADJUSTMENT Select Cable ADJUSTMENT CONTROL SYSTEMS > Select Cable ADJUSTMENT 1. Shift the select lever to “N” range. 2. Lift up the vehicle. 3. Remove the center exhaust pipe. Center Exhaust Pipe > REMOVAL 4. Remove the center...
Select Cable REMOVAL Select Cable REMOVAL CONTROL SYSTEMS > Select Cable REMOVAL 1. Shift the select lever to “N” range. 2. Disconnect the ground cable from battery. NOTE NOTE: For the 12 volt engine restart battery of HEV model, disconnect...
MT Gear Shift Lever ASSEMBLY MT Gear Shift Lever ASSEMBLY CONTROL SYSTEMS > MT Gear Shift Lever ASSEMBLY NOTE: • Clean all the parts before assembly. • Apply NIGTIGHT LYW No. 2 grease or equivalent to each part. General Description > COMPONENT 1. Mount...
MT Gear Shift Lever DISASSEMBLY MT Gear Shift Lever DISASSEMBLY CONTROL SYSTEMS > MT Gear Shift Lever DISASSEMBLY 1. Remove the lock wires. (A) Lock wire 2. Remove the rod from gear shift lever. (A) Rod (B) Lever (C) Stay...
MT Gear Shift Lever INSPECTION MT Gear Shift Lever INSPECTION CONTROL SYSTEMS > MT Gear Shift Lever INSPECTION 1. Check the parts (bushing, cushion rubber, spacer, boot, stay and rod, etc.) for deformation, damage and wear. If necessary, correct or replace faulty parts. Compare the...
MT Gear Shift Lever INSTALLATION MT Gear Shift Lever INSTALLATION CONTROL SYSTEMS > MT Gear Shift Lever INSTALLATION 1. Insert the gear shift lever from the room side. NOTE: Insert the rod and the stay, and then temporarily set them onto the transmission mount. 2. Lift up...
MT Gear Shift Lever REMOVAL MT Gear Shift Lever REMOVAL CONTROL SYSTEMS > MT Gear Shift Lever REMOVAL 1. Disconnect the ground cable from battery. 2. Remove the console box. Console Box > REMOVAL 3. Remove the gear shift knob and remove the cover - shift lever....
General Description COMPONENT General Description COMPONENT CONTROL SYSTEMS > General Description COMPONENT 1. AT SELECT LEVER (1) Grip sub ASSY (model with gate shifter) (14) Spacer pin guide (27) Nut (2) Clamp grip pin (15) Plate COMPL...
General Description PREPARATION TOOL General Description PREPARATION TOOL CONTROL SYSTEMS > General Description PREPARATION TOOL 1. SPECIAL TOOL ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS 1B022XU0 SUBARU SELECT MONITOR III KIT Used for setting of each...
AT Shift Lock Solenoid and Range Switch INSTALLATION AT Shift Lock Solenoid and Range Switch INSTALLATION CONTROL SYSTEMS > AT Shift Lock Solenoid and “P” Range Switch INSTALLATION Install in the reverse order of removal. NOTE: Insert the solenoid unit terminals to the harness connector. (A)...
AT Shift Lock Solenoid and Range Switch REMOVAL AT Shift Lock Solenoid and Range Switch REMOVAL CONTROL SYSTEMS > AT Shift Lock Solenoid and “P” Range Switch REMOVAL 1. SOLENOID UNIT 1. Remove the AT select lever. Select Lever > REMOVAL 2. Remove the spacer and gasket. Select Lever >...
AT Shift Lock Control System LOCATION AT Shift Lock Control System LOCATION CONTROL SYSTEMS > AT Shift Lock Control System LOCATION 1. MODEL WITHOUT PUSH BUTTON IGNITION SWITCH (1) TCM (“P” range) (4) Key cylinder (with built-in key warning switch) (6)...
ELECTRICAL SPECIFICATION ELECTRICAL SPECIFICATION CONTROL SYSTEMS > AT Shift Lock Control System ELECTRICAL SPECIFICATION • Model without push button ignition switch Item Connector No. Terminal No. Input/Output signal Measured value and...
AT Shift Lock Control System WIRING DIAGRAM AT Shift Lock Control System WIRING DIAGRAM CONTROL SYSTEMS > AT Shift Lock Control System WIRING DIAGRAM 1. MODEL WITHOUT PUSH BUTTON IGNITION SWITCH (1) Ignition switch (5) TCM (shift range information) (9) Battery (2) Stop...
General Description SPECIFICATION CONTROL SYSTEMS > General Description SPECIFICATION Item Specifications Swing torque of rod against lever N (kgf, lb) 3.7 (0.38, 0.83) or less
Select Lever INSPECTION CONTROL SYSTEMS > Select Lever INSPECTION 1. Inspect the removed parts by comparing with new parts for deformation, damage and wear. Repair or replace if defective. 2. Inspect the select lever assembly operating...
Select Cable INSPECTION CONTROL SYSTEMS > Select Cable INSPECTION Check the removed cable and replace or adjust if damaged, rusty or malfunctioning. 1. Check the cable for smooth operation. 2. Check the inner cable for damage and rust....
General Diagnostic Table INSPECTION CONTROL SYSTEMS > General Diagnostic Table INSPECTION Symptoms Possible cause Corrective action Select lever Starter does not run. Adjust the select cable and inhibitor switch, or inspect the...
General Description CAUTION CONTROL SYSTEMS > General Description CAUTION • Wear appropriate work clothing, including a cap, protective goggles and protective shoes when performing any work. • Remove contamination including dirt and...