SUBARU impreza SERVICE and USER MANUAL

EyeSight

Sort by: default name
Switches and Harness INSPECTION Switches and Harness INSPECTION EyeSight > Switches and Harness INSPECTION 1. Measure the resistance between connector terminals. Preparation tool: Circuit tester • Pre-collision brake OFF switch Terminal No. Inspection...
Stereo Camera INSTALLATION Stereo Camera INSTALLATION EyeSight > Stereo Camera INSTALLATION CAUTION: • Do not remove the protective cover until just before installing the stereo camera cover assembly. Using the bolt and nut, install the stereo camera with the...
Stereo Camera REMOVAL Stereo Camera REMOVAL EyeSight > Stereo Camera REMOVAL CAUTION: • When the stereo camera or windshield glass has been replaced, removed or installed, always perform the adjustment and inspection of the camera. (When the stereo camera...
Relay and Fuse INSPECTION Relay and Fuse INSPECTION EyeSight > Relay and Fuse INSPECTION 1. CHECK FUSE 1. Remove the fuse and inspect visually. 2. If the fuse is blown out, replace the fuse. NOTE: If the fuse is blown again, check the system wiring harness....
Relay and Fuse LOCATION Relay and Fuse LOCATION EyeSight > Relay and Fuse LOCATION Relay & fuse box Fuse 15 A (stop light and brake switch, brake relay) (A) NOTE: For other related fuses, refer to the wiring diagram. Power Supply Circuit
General Description COMPONENT General Description COMPONENT EyeSight > General Description COMPONENT 1. STEREO CAMERA (1) Shim (washer) (4) Stereo camera cover ASSY Tightening torque: N·m (kgf-m, ft-lb) (2) Camera plate (5) Cap T:...
General Description PREPARATION TOOL General Description PREPARATION TOOL EyeSight > General Description PREPARATION TOOL 1. SPECIAL TOOL ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS 87599VA000 (Newly adopted tool) RANDOM CHART Used for adjusting stereo...
Cruise Control Command Switch INSPECTION Cruise Control Command Switch INSPECTION EyeSight > Cruise Control Command Switch INSPECTION 1. Measure the resistance between connector terminals. Preparation tool: Circuit tester Terminal No. Inspection conditions Standard 3 — 9...
EyeSight System WIRING DIAGRAM EyeSight > EyeSight System WIRING DIAGRAM Refer to “EyeSight System” in the wiring diagram. EyeSight System > WIRING DIAGRAM
VDC Control Module and Hydraulic Control Unit (VDCCM H-U) NOTE EyeSight > VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) NOTE For the operation procedures for VDC control module & hydraulic control module (VDCCM&H/U), refer to “VEHICLE DYNAMICS CONTROL (VDC)”...
Transmission Control Module (TCM) NOTE EyeSight > Transmission Control Module (TCM) NOTE For the operation procedures for transmission control module (TCM), refer to “CONTINUOUSLY VARIABLE TRANSMISSION” section. Transmission Control Module (TCM)
Switches and Harness NOTE EyeSight > Switches and Harness NOTE 1. PRE-COLLISION BRAKE OFF SWITCH & LANE DEPARTURE WARNING OFF SWITCH The pre-collision brake OFF & lane departure warning OFF switch is integrated in the stereo camera cover...
Stop Light Brake Switch NOTE EyeSight > Stop Light & Brake Switch NOTE For the operation procedures for stop light and brake switch, refer to “BRAKE” section. Stop Light Switch
Roll Connector NOTE EyeSight > Roll Connector NOTE For the operation procedures for roll connector (steering angle sensor), refer to “AIRBAG SYSTEM” section. Roll Connector
Power Steering Control Module NOTE EyeSight > Power Steering Control Module NOTE For the operation procedures for power steering control module, refer to “POWER ASSISTED SYSTEM (POWER STEERING)” section. Power Steering Control Module
Multi-function Display (MFD) NOTE EyeSight > Multi-function Display (MFD) NOTE For the multi-function display (MFD), refer to “INSTRUMENTATION/DRIVER INFO” section. Multi-function Display (MFD)
Cruise Control Command Switch NOTE EyeSight > Cruise Control Command Switch NOTE For the operation procedures for the EyeSight steering switch, refer to “CRUISE CONTROL SYSTEM” section. Cruise Control Command Switch
Combination Meter NOTE EyeSight > Combination Meter NOTE For the operation procedures for combination meter, refer to “INSTRUMENTATION/DRIVER INFO” section. Combination Meter
Body Integrated Unit NOTE EyeSight > Body Integrated Unit NOTE For the operation procedures for body integrated unit, refer to “STARTING/CHARGING SYSTEMS” section. Body Integrated Unit
General Description LOCATION EyeSight > General Description LOCATION Refer to “LOCATION” of “EyeSight (DIAGNOSTICS)” section. Electrical Component Location > LOCATION
EyeSight System INSPECTION EyeSight > EyeSight System INSPECTION Refer to “Basic Diagnostic Procedure” of “EyeSight (DIAGNOSTICS)” section. Basic Diagnostic Procedure
Diagnostics with Phenomenon INSPECTION EyeSight > Diagnostics with Phenomenon INSPECTION Refer to “Diagnostics with Phenomenon” of “EyeSight (DIAGNOSTICS)” section. Diagnostics with Phenomenon
General Description CAUTION EyeSight > General Description CAUTION • Before disconnecting connectors of sensors or units, be sure to disconnect the ground cable from battery. When replacing the electrical parts provided with memory functions...
Control Unit NOTE EyeSight > Control Unit NOTE System control of the EyeSight is performed by each module. For procedure, refer to the following sections. • Engine control module (ECM): Engine Control Module (ECM) •...