SUBARU impreza SERVICE and USER MANUAL

STARTING-CHARGING SYSTEMS(H4DO(w-o HEV))

Sort by: default name
Starter INSPECTION Starter INSPECTION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Starter INSPECTION 1. ARMATURE 1. Check the commutator for signs of seizure or stepped wear caused by roughness of the surface. If there is light wear, use sandpaper to...
Starter INSTALLATION Starter INSTALLATION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Starter INSTALLATION Install in the reverse order of removal. NOTE: For CVT model, a nut is used at (A). Tightening torque: 50 N·m (5.1 kgf-m, 36.9 ft-lb)...
Starter DISASSEMBLY Starter DISASSEMBLY STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Starter DISASSEMBLY 1. Disconnect the terminal M from the magnet switch assembly. 2. Remove the magnet switch assembly from the starter housing assembly. 3....
Starter REMOVAL Starter REMOVAL STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Starter REMOVAL 1. Disconnect the ground cable from battery. 2. Remove the clip (A) from the air intake boot. 3. Loosen the clamp (B) securing the air cleaner...
Generator INSTALLATION Generator INSTALLATION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Generator INSTALLATION 1. Temporarily install the generator bracket to the engine main body and tighten the bolts in the numerical order. Tightening torque: 36 N·m...
Generator ASSEMBLY Generator ASSEMBLY STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Generator ASSEMBLY Assemble in the reverse order of disassembly. NOTE: • Refer to component for tightening torque of each part. General Description > COMPONENT...
Generator DISASSEMBLY Generator DISASSEMBLY STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Generator DISASSEMBLY 1. Remove the cap from the generator. 2. Remove four bolts. 3. Use a drier to heat the rear cover (A) portion to 50 — 60 ° C...
Generator INSPECTION Generator INSPECTION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Generator INSPECTION 1. DIODE CAUTION: There is the possibility of damaging the diodes if a mega-tester (used to measure high voltages) or a similar measuring instrument is...
Generator REMOVAL Generator REMOVAL STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Generator REMOVAL 1. Remove the V-belt covers. 2. Disconnect the ground cable from battery. 3. Remove the V-belts. V-belt > REMOVAL 4. Disconnect the...
General Description COMPONENT General Description COMPONENT STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > General Description COMPONENT 1. STARTER (1) Starter housing ASSY (9) Overrunning clutch (17) Sleeve bearing (2) Sleeve bearing (10)...
General Description SPECIFICATION General Description SPECIFICATION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > General Description SPECIFICATION Item Specifications Vehicle model CVT MT Starter Type Reduction type Model M000T38571 M000T33176...
Battery Current Temperature Sensor INSTALLATION Battery Current Temperature Sensor INSTALLATION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery Current & Temperature Sensor INSTALLATION 1. BATTERY CURRENT SENSOR Install in the reverse order of removal. Tightening torque: General Description > COMPONENT...
Battery Current Temperature Sensor INSPECTION Battery Current Temperature Sensor INSPECTION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery Current & Temperature Sensor INSPECTION 1. BATTERY CURRENT SENSOR CAUTION: Pay attention to polarity when checking the resistance in the battery current sensor....
Battery Current Temperature Sensor REMOVAL Battery Current Temperature Sensor REMOVAL STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery Current & Temperature Sensor REMOVAL 1. BATTERY CURRENT SENSOR NOTE: Remove the battery current sensor and battery cable as a unit. 1. Disconnect the battery...
Battery INSTALLATION Battery INSTALLATION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery INSTALLATION CAUTION: After the battery is installed, initial diagnosis of the electronic throttle control is performed. Wait for 10 seconds or more after turning the...
Battery REMOVAL Battery REMOVAL STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery REMOVAL 1. Disconnect the positive (+) terminal after disconnecting the negative (−) terminal of battery. 2. Remove the battery cable holder from the battery...
General Description PREPARATION TOOL STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > General Description PREPARATION TOOL 1. GENERAL TOOL TOOL NAME REMARKS Circuit tester Used for measuring resistance, voltage and current. NOTE: •...
General Description CAUTION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > General Description CAUTION • Prior to starting work, pay special attention to the following: 1. Always wear work clothes, a work cap, and protective shoes....
Battery INSPECTION STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery INSPECTION WARNING: • As batteries produce flammable gases, be careful not to bring an open flame close to the batteries. • Ventilate sufficiently when...
Battery CHARGE STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Battery CHARGE WARNING: • Do not bring an open flame close to the battery when working. CAUTION: • Prior to charging, corroded terminals should be cleaned...
Starter ASSEMBLY STARTING/CHARGING SYSTEMS(H4DO(w/o HEV)) > Starter ASSEMBLY 1. Apply grease to the shaft sliding surfaces of the internal gear assembly. Grease: Multemp #6129 or equivalent 2. Assemble the shaft to the...